EASYKA 1 The stant keypad access control unit suitable for extern tions.The unit accepts up to 500 users and provides entry via 2. MAOpe 4 VAC/DC
EASYKA 10 ming the EASYKA is done solely via the unit's keypad driven P ra Certain codes and settings are pr ry Settings. The table below s
EASYKA 8.1 Entering Programming Mode 11 e Programming Code is the door and theogramming Mode. NOTE1. Press the "#" key two times. Mo
EASYKA 12 ChT O method to quickly test the Lock Strike The D ng for the Open Code is 2580. W n ntroller, the default Open Code w y for a newe e
EASYKA 13 10. Changing the Auxiliary Code ethod to quickly test the fault Auxiliary ter Programming Mode. The Mode LED will turn orange. . ill
EASYKA 14 NOTE Programming Code can not be erased, i.e. the code 00not valid and will not erase the Programming Code. 00 is gramming Mode 4:
EASYKA 15 fining Auxiliary1. EMode. 6: the Mode LED will L’E returns to Normal o Mode LED will turn green. 14. De Inputs/Outputs GREEN G
EASYKA 16 Auxiliary Mode AuxA RelayTime Settings (All times and delay are in seconds) iliary Input Auxiliary Ouput Aux. ctivated On 0 REX-2 l
EASYKA 17 g F re ation aStrike Release Time 1. 2. green. 3. below: First Digit: 15. Settin ail Safe/Secu Oper nd Lock GREENGREEN GREENEnter Prog
EASYKA 18 Secondary Codes can only be enrolled to User Slot that dary ot have to be unique, i.e. multiple me Secondary Code. t be the same
EASYKA 19 will flash green, indicating controller is ready to accept a Secondary Code. e controller will return 4. Enter Seconis validis reads
EASYKA 2 3. MOUNTING ation to mount the EASYKA controller. Before starting, select the locThis location should be at shoulder height and on the
EASYKA 20 16.2 E ingM1. En2. Pre3. Ennumflaswof Sec5. y Code., If the Secondary Code is valid the controller will beep three times and retur
EASYKA 21 Method the 3. codes . ing Code is valid, yeturn to Normal ill hear a long17.2 Codes using th2. 3. 4. belonging to the user you wan
EASYKA 22 As he Standard Method W user, that user is assigned rights to activate the Lock Strike Relay when they present a valid code t Menu all
EASYKA 23 18.2 1. 2. Press "9" to enter Menu 9: The Mode LED will turn green. 3. Enter the 3-digit User Slot 000: The Door LED will f
EASYKA 24 When the built-in keypad heater is active it will require additional The isabled, to Warnpower. factory default setting for the keypa
EASYKA 25 est be in Normal Mode otherwise this will not LED is green before 123 X button pressed 45 program a new Programming nit using the initi
EASYKA 3 BLACKGREENWHITEBROWNBLUEYELLOWORANGEPURPLEGRAYGROUNDREX / BLIN / MONITORLOCK: COMAUX: COMN.O.N.C. REDV INPUTCOLOR DESCRIPTIONN.
EASYKA 4 .2 Wiring the Lock Strike Relay and REX 3 ELECRTIC LOCK STRIKE FAIL SAFE MON POWER SUPPLY12V – 24V DC (-) (-)(-)B
EASYKA 5 .3 Wiring the Auxiliary Input and Output 3 N PO R SUPPLY – 24V DC Auxiliary Relay(+) (-) (-) IN / MONITOR N.C. N.O. COM COMMO
EASYKA 6 4. NORMAL, SECURE & MASTER USERS the use of PIN codes. Each user is provide ith two code memory slots, emory Slot 1 (Primary Code)
EASYKA 5. Modes of Operation The EASYKA has 3 Modes of Operation: 1. Normal Mode Normal Mode is the default mode and the Mode LED is green. In Normal
EASYKA 8 Operation 5.1.1 Changing from Normal Mode to Se5.1 Changing the Modes ofcure Mode: e Code is 3838. tting for the Normal / Securt Nor
EASYKA 9 5.1.4 Changing from Bypass Mode to Normal Mode: GREEN To set the Normal/Bypass code refer to par 13. 1. Enter the 4 digit Normal / B
Commentaires sur ces manuels